Maintenance & Troubleshooting Guide For Blow Molding Machines

Nov 14, 2026

Leave a message

 

 

Blow molding machines stand as indispensable workhorses within the plastic packaging sector. Designed to shape PET, PP and other thermoplastic materials into finished plastic containers, they serve beverage, food, personal care and pharmaceutical production lines all over the world. The whole forming process follows a clear logic: preformed plastic parisons are first heated until they reach a soft, malleable state. High-pressure compressed air is then injected inside the heated parison, pushing the material outwards to fit tightly against the inner surface of precision molds. Once cooled down, neatly shaped plastic bottles are released. Thanks to its high throughput, cost advantages and flexible customization for different bottle designs, this automated equipment has become a standard fixture on modern filling and packaging lines.

Fully Automatic Blow Molding Machine
Fully Automatic Blow Molding Machine

 

Even with robust construction, blow molders run into a range of typical operational issues from time to time. Uneven heating across parisons, insufficient blowing air pressure and misaligned molds are among the most frequent headaches for on-site technicians. Safety always comes first before any repair work starts - power supply must be fully cut off and the machine locked out. For heating irregularities, technicians can verify the performance of temperature control modules and use a multimeter to test the resistance of heating tubes; faulty heating elements should be replaced right away. When pressure or air leakage occurs, the whole pneumatic circuit needs inspection. Solenoid valves and air cylinders are common leakage points, and worn sealing rings are usually the culprit that needs replacement. On the mechanical side, keep a close eye on timing belt tension and bearing wear, adjusting or swapping out worn components as required. From an electrical perspective, check feedback signals from sensors and confirm the PLC program operates as intended. Dust buildup on photoelectric sensors can trigger false alerts, so regular cleaning is necessary. Keeping detailed service logs is a smart habit, which makes recurring faults much easier to trace and resolve later.

 

Routine maintenance is the foundation that cuts down unexpected breakdowns and extends the machine's service life. Before starting production each day, operators should confirm the air supply stays stable between 0.6 MPa and 0.8 MPa. Mold surfaces need wiping clean of residual plastic deposits, and sliding rails, guide pins and other moving assemblies require proper lubrication. On a weekly schedule, tighten loose terminals inside the heating circuit, clean clogged fan filters and check the hydraulic fluid level. Monthly tasks include regreasing drive chains and gearboxes, retightening electrical connections and blowing dust out of the control cabinet. If the unit will sit idle for an extended period, drain all trapped moisture from the pneumatic system. Coat molds, heating tubes and other critical metal parts with anti-rust oil, and cover the equipment to shield it from dust and humidity. Following a structured maintenance checklist consistently keeps downtime under control and sustains stable output.

Fully Automatic Blow Molding Machine
Frequently Asked Questions
 
 

What tests should be carried out right after maintenance before formal production starts?

+

-

After finishing all maintenance items, run the machine with no load for 5 to 10 minutes. Listen carefully for abnormal noise or jamming movements. Confirm blow pins and exhaust valves act smoothly, and molds close accurately without air leakage or system alarms. Only after passing this idle check can operators feed parisons in for trial runs.

What rules should we follow for lubricants and hydraulic oil during basic maintenance?

+

-

Never mix hydraulic oils or lubricants of different grades. If the liquid level drops, top it up only with the same product type. Replace the oil completely and clean the reservoir promptly once you spot cloudiness, sediment or contaminants inside.

How do we fix parison feeding jams in simple steps?

+

-

Shut down power and lock out the machine first. Clear plastic scraps stuck on guide rails and pulleys. Adjust belt tension until you can press the belt and feel mild elasticity. If the belt has cracks or heavy wear, install a new belt with matching specifications and test the feeding movement afterward.

What is the quick fix for leaks in pneumatic or hydraulic circuits?

+

-

Locate the leaking joint and gently fasten it with a spanner. If tightening does not stop the leak, swap out the O-ring seal at the connection point. Recheck after replacement to make sure no air or fluid escapes and pressure holds steady.

Which key spots demand lubrication during weekly maintenance?

+

-

Apply suitable lubricating oil or grease to all moving parts: feeding rails, drive chains and gears, blow pin guide sleeves and mold guide pillars. Take extra care not to smear lubricant onto mold cavities or parison contact areas, as contamination will ruin finished bottles.

Send Inquiry
Contact us if have any question

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.

Contact now!